How To Manually Roll Up Power Windows

How to Raise a Stuck Ability Window Manually in a Car

I learned valuable DIY skills from my dad who was an electric engineer and physicist; I took a twelvemonth of auto in high school.

How to Raise a Stuck Power Window Manually — How to Heighten a Stuck Power Window Manually

Mr Thinktank, CC BY 2.0, via flickr

Quick Fix for a Ability Window That Won't Go Up

Did your power window get stuck in the down position? Are y'all trying to avoid an expensive bill from the auto-mechanic? Are yous worried about leaving your window down? This quick fix will let you to pull a stuck window up manually. Afterwards y'all get that taken care of, you can either accept it to the mechanic or purchase the replacement motor yourself for the repair.

How to Fix a Stuck Car Window Manually

The principles for fixing a stuck window volition be the same or quite similar whether yous have a 2000 Toyota Camry, a 1997 Toyota 4Runner, a 2001 Mazda, or some other automobile model. I've had this issue with my 1997 Toyota 4Runner earlier. Here'southward what you volition demand and here'due south what to do:

Remove the door panel.
Disconnect the window from the motor.
Undo the motor.
Heighten the window.
Reconnect the motor.
Supercede the door panel.

Supplies

Flat-head screwdriver
Tape
2 Safe bands
two pieces of forest (approx. 12-inches in length); alternatively you tin can employ painter's tape

Safety

Every bit a general give-and-take of caution, e'er be conscientious when working with electric equipment and wiring and wear PPE. Never effort anything beyond your skill level.

Scroll to Continue

Step ane: Remove the Door Panel

Remove all screws on the door console: Remove the screws on the front of the driver's-side door panel (they may be plastic or metallic). Be sure to locate all screws—some will be under plastic covers, behind a door handle, beside a courtesy lite, etc. Remove the plastic covers during this procedure and set them bated. (Always put your screws in a safe place.)
Remove the door console: Remove the door console using a apartment-head screwdriver past prying it gently out.
Disconnect the ii plastic wire switches: You lot tin utilise a flat-head screwdriver to pull the connectors apart. Put the door panel bated.
Remove the door console: Using your hands or a flat-caput screwdriver, gently start at the front edge of panel and pry information technology off. Work your manner along the sides and to the dorsum of the door frame. The plastic snaps should disengage. Elevator the door panel off.
Remove the polyethylene cover: You can utilise a razor bract to remove it instead of pealing it entirely off or merely cut it along the inside of the auto (encounter the video beneath).

Step 2: Disconnect the Window From the Motor

Get two pieces of wood: Get 1–2 pieces of wood (1-foot-long is fine) that will serve as braces for holding the window in identify from the inside of the door (you tin can also use painter's record). You volition need to hold the window up once you lot remove the screws of the regulator mechanism so that the window does not fall off the regulator machinery.
Locate the regulator machinery screws: There will probable exist two screws that are holding the window to the regulator mechanism that you volition need to remove—these are often seated and visible through the door frame. When you unscrew them, be sure to hold the window so that it won't accidentally fall off the regulator machinery'due south ledge (this is an extra precaution).
Move the window up: While holding the window in place with one mitt below, catch the top of the window and pull it upward equally loftier equally you can. Stick a piece of wood into the frame to concord the window in place.

Stride 3: Disengage the Motor

Locate the motor and remove the bolts/basics: Find the motor in the door. It's often located in the superlative right of the frame. Remove the bolts and nuts property it in place.
Remove the encompass: Remove the cover but offset secure the nuts in the base of the encompass with tape (to preclude them from getting lost) earlier unscrewing. The cover will have a magnetized pull when you remove information technology.
Remove the motor axle: The brushes along the beam are spring-loaded and volition popular out if the axle is removed, so use 2 rubber bands to concur them in place. Have one ring and thread information technology through the wire that leads to the brushes; loop it back through its own end and over a section of the regulator to secure information technology. Repeat this for the other brush with a second prophylactic band. You can so lift the motor axle out of the motor trunk by turning information technology counter-clockwise. Set it aside.

Accessing (Repairing) the Car Window Motor

Step 4: Connect the Window and Motor and Raise the Window

Replace the screws: While grabbing the window from higher up and below, supplant the screws that agree the regulator mechanism ledge and remove the slice of wood holding the window in place.
Enhance the window: While property the window from in a higher place and below, push and lift the window up; you tin be more forceful hither while lifting to really go the window high enough. Ever keep your manus belongings the window from beneath then that the window stays upward.
Put the motor axle back in place: Employ your free hand to put the motor axle back in place into the motor trunk; careful not to force it. While keeping the window in place, turn the axle clockwise to rest information technology into the motor body, keeping the brushes aligned with their original position with the commutator. Turn the axle every bit far equally yous can (the window should be lifted up); you tin can now release both the window and the beam.
Replace the motor cover: Very carefully, supervene upon the motor encompass and be sure to mind the magnetization—practice not knock the beam out of identify. Replace the bolts.
Secure the motor to the door frame: Fix the motor to the door frame once again by threading the bolts/nuts back in place. You tin can necktie off the wires to the door—do non reconnect them since you're not going to use the window.

Step v: Supervene upon the Door Panel

Replace the polyethylene cover.
Put the door console back. This is a multistep process: start by inserting the door handle into the panel and fit the top-rear edge of the door panel into the top lip of the door frame. Snap the door console back into place and connect the plastic wire connectors. Y'all may need to crash-land the panel dorsum into place forth the edges of the frame.
Replace the screws. Replace the screws that you removed at the start of the project.

This article is authentic and true to the best of the author's cognition. Content is for informational or entertainment purposes only and does non substitute for personal counsel or professional communication in business concern, fiscal, legal, or technical matters.

If you're thinking about trying to come up up with some absurd motorcar proper noun ideas for your vehicle, then this is the article to give y'all a jump first on the process.